PM2.5 or Particle Counts? Choosing the Right Metric for the Job

0 comments

PM2.5 or Particle Counts? Choosing the Right Metric for the Job

AI-generated product illustration based on Temtop references. Office PM2.5 trends and professional cleanroom particle checks are separate tasks. Display values are illustrative.

At nine on a Monday morning, a facilities manager walks past the air monitor on the office floor. The PM2.5 reading is higher than it was before people arrived. Later that day, the team plans to change a filter and wants to know what to look for in the data.

In a cleanroom across town, another team is preparing to measure airborne particles at designated locations. They also need a particle reading, but their procedure calls for counts at specified particle sizes.

Both teams are asking about particles in the air. The office team wants to understand how fine-particle levels change during the workday. The cleanroom team needs data that can be checked against a defined classification procedure. The difference between those tasks is a good place to start when choosing a monitor.

One air sample, two ways of describing particles

PM2.5 describes mass concentration. It refers to the fine-particle fraction associated with an aerodynamic diameter of about 2.5 micrometres or less and is commonly reported in micrograms per cubic metre (µg/m³). If the reading rises, the monitor is indicating an increase in estimated fine-particle mass per volume of air at that location. [1]

Particle counting describes how many particles are detected by size. A counter samples a volume of air and reports counts by size channel. A cumulative channel counts particles at or above a specified size. A differential channel reports a size band. When comparing reports, check the channel convention and whether the numbers are raw counts or concentrations normalised to a volume. For cleanroom classification under ISO 14644-1, the measurements are based on cumulative concentrations at specified particle sizes and designated sampling locations. [2]


Figure 1. Particle mass and particle number describe different properties of an air sample. The dots illustrate the concept and represent no measured values.

Picture a sample with many small particles and another with fewer, heavier particles. The samples can have similar total particle mass and very different counts. The conversion depends on what is known about size distribution, density and other particle properties. Optical instruments also respond to properties such as size and composition, which matter when interpreting the relationship between the reported reading and a reference measurement. [1]

Match each instrument to its monitoring task

For an office team investigating PM2.5 trends, the Temtop M10+ Wi-Fi is an indoor monitoring example. For a cleanroom team collecting size-resolved particle counts, the PMD 331 is a professional particle-counter example. These are two distinct project briefs. Temtop lists seven particle-size channels for the PMD 331, while the M10+ Wi-Fi provides PM2.5 and other indoor measurements. [6] [7]

The dots in an illustration explain quantities. Their drawn size does not define a PM2.5 cutoff or an instrument channel. PM2.5 uses an aerodynamic size convention, while optical particle sizing depends on how particles scatter light. Review the reported metric and method before interpreting a result. [1] [5]

Back at the office, what would a useful PM2.5 record look like?

Start before the filter change. Keep the monitor in a consistent location, allow it to record through a typical occupied period and write down events that might affect the trend. Did the cleaning crew arrive? Was maintenance under way nearby? Was an outside door held open for deliveries? Indoor particle concentrations can reflect both outdoor air and activities inside the building. [3]

After the change, compare similar periods with the same location, units and averaging interval. If the reading falls, look at how long the difference lasts and whether it recurs under similar conditions. A lower reading gives the team a reason to keep investigating. If occupancy, outdoor conditions or operating hours changed as well, record those differences before drawing a conclusion about the filter.

Use this comparison to review the room trend. Calculating filter efficiency requires a defined test arrangement, including appropriate upstream and downstream measurements. A change in ambient room concentration, with several changing influences, is insufficient to calculate that efficiency. [8]

The time record also helps when the monitor shows a sharp peak. Check when it began, how long it lasted and what was happening nearby. The record can narrow down the next question to ask. A particle reading alone has limited ability to identify a source, and the performance of some indoor monitors depends on factors such as humidity, placement and the mix of pollutants. [4]

Figure 2. A practical comparison keeps the monitoring point and recording interval consistent, with operating changes documented alongside the readings.

AI-generated office scene based on the official Temtop M10+ Wi-Fi reference. Log a filter change alongside the room trend. This scene represents ambient monitoring.

At a cleanroom, start with the procedure

The cleanroom team has a different starting point. Before choosing the counter, confirm the classification requirement, the particle sizes and the sampling conditions. Then check that the counter’s channels, sample volume, reporting format and supporting instrument documentation meet the needs of the job. A reading can only be assessed in the context of the method used to obtain it. [2]

When a project requires formal cleanroom classification, ISO 14644-1 addresses the classification method, and ISO 21501-4 addresses calibration and verification of light-scattering airborne particle counters. The project quality owner should confirm the required channels, sample volumes and locations, room operating state and current instrument records. Temtop’s PMD 331 page states that individual-unit ISO certificates are optional. Request the documents required by the project before deciding that a particular unit is suitable. [2] [5] [6]

For a portable dust investigation, the brief may be different again. The team may want to compare dust readings across a route or before and after an activity. First agree which mass fraction matters, how long to sample at each point and which operating conditions to log. That makes it possible to compare observations on the same basis.

What are you trying to decide?

Start with

Confirm before selecting the instrument

When do fine-particle levels change in an occupied office?

PM2.5 mass concentration over time

Recording interval, history access and where the monitor will sit

Where do particle levels rise during a dust investigation?

The mass fraction relevant to the task

Sampling intervals, comparable conditions and field records

Does a cleanroom meet the specified classification?

Particle number concentration at the required sizes

Size channels, sampling requirements and instrument documentation

AI-generated professional scene based on the official Temtop PMD 331 reference. Confirm the sampling plan and current instrument documentation for the project.

 

Product examples. Temtop’s M10+ Wi-Fi displays PM2.5 mass concentration. The PMD 331 reports counts by particle-size channel. Screen values are from the official product imagery.

A routine you can take into the next project

1.  Write the decision first. “We want to know when particle levels change across the workday” is a different brief from “We need data for a cleanroom classification procedure.”

2.  Name the measurement. Record the metric, units and any size channel or time interval that the decision depends on.

3.  Match the instrument and method. Check what the instrument measures, how it reports the result and which operating conditions it supports.

4.  Keep the context with the reading. Log the location, time and events that could matter when someone reviews the data later.

Temtop works across indoor air monitoring, aerosol dust monitoring and particle counting. If you’re comparing instruments for a project, share the decision you need to make, the setting and the measurement your procedure calls for. Those details give the conversation a concrete starting point.

In the next issue, we’ll take the office example one step further. Once you know what to measure, where should the monitor go?

References

1.  U.S. Environmental Protection Agency. Document Display (PURL) | NSCEP | US EPA.

2.  International Organization for Standardization. ISO 14644-1:2015, Classification of air cleanliness by particle concentration.

3.  U.S. Environmental Protection Agency. Sources of Indoor Particulate Matter (PM) | US EPA.

4.  U.S. Environmental Protection Agency. Low–Cost Air Pollution Monitors and Indoor Air Quality | US EPA.

5. ISO. ISO 21501-4:2018 — Airborne particle-counter calibration and verification.

6. Temtop. PMD 331 product page and certificate notice.

7. Temtop. M10+ Wi-Fi product page.

8. ASHRAE. CHAPTER 29 AIR CLEANERS FOR PARTICULATE CONTAMINANTS.

Leave a comment

All blog comments are checked prior to publishing
You have successfully subscribed!
This email has been registered